1
O—ring 34.4x3.1 (IDxd)
2 O—ring 24.4x3.1 (IDxd)
3 Sealing ring 148.59x33 (IDxd)
4 O—ring 73.02x3.53 (IDxd)
5 O—ring 49.2x3.53 (IDxd)
6 O—ring 69.4x3.1 (IDxd)
7 O—ring 79.6x5.7 (IDxd)
8 Sealing ring of the side door 253.37x6.99
9 Dirt collector of the locking shaft 2S91.03.16
10 Sealing piston cuff 2S91.03.12
11 V-shaped O-ring 2S91.03.09
12 Sealing cuff 2S91.03.11
13 The mechanical seal is blind 2S91.01A.01.00
14 Pipe mechanical seal 2S91.01B.01.00
15 Upper seal 2S91.01A.03.00
1 O-shaped sealing ring PUG.1835-FN1835-09
2 O-shaped sealing ring PUG.1835-FN1835-11
3 O-ring housing 390x13.7 PUG.1835-FN1835—14/15
4 O-ring of the support ring 484x13.7 PUG.1835-FN1835—12/13
5 Piston O-ring 610x13.7 PUG.1835-FN1835—19/20
a. SL450 SWIVEL
1 AD450001-2200B1- Clutch assembly
2 AD45000-2300B1 - Air motor assembly
3 AD450001-21- Protection plug
4 4301040032 - Bearing 2007140
5 53030114250 - Oil seal PD250×290×18
b. JC-70D DRAWWORKS
1 PS702407-00- Hydraulic disc brake pads
c. JC-70D DRAWWORKS DRUM SHAFT ASSEMBLY
1 43011001- Bearing UN240
d. AIR CONTROL SYSTEM FOR THE JC-70D DRAWWORKS
1 5127041106 - Shuttles valve ND5
2 5127043006 - Handle reversing valve (2-HA-3)
3 5127043006 - Handle reversing valve (2-HA-2Z)
4 5127043006- Handle reversing valve (2-HA-2)
5 5127043006 - Handle reversing valve (2-HA-1)
6 5127043106 - Button valve (ND7)
7 5127010102 - Control Valve Box assembly
8 44120501001 - Stainless steel ball valve Rc1/2
9 5127040706 - Rapid escape valve G1/2 (ND12)
10 5127040706 - Rapid escape valve G3/8 (ND10)
"SCHEDULE 1B: JZ70D DRILLING RIG ROTARY
SYSTEM MECHANICAL SPARES"
a. ZP375 ROTARY TABLE DRIVE CASE
1 4801010140- Chain 24S-4X122 (122 section)
2 4801010140- Chain 24S-4X134 ( 134 section)
"b. ZP375 ROTARY TABLE OUTPUT SHAFT
ASSEMBLY"
1 BG322004-031300- Oil ring unit
2 T104-002.00- Pneumatic tyre clutch L T500/125
3 43010300222- Bearing 22228C/W33 (φ140Xφ250X68)
4 42020104071- Bolt with holeM10X30 (GB/T5780)
"SCHEDULE 1C: JZ70D DRILLING RIG
CIRCULATION SYSTEM MECHANICAL SPARES"
a. MUD PUMP F1600
1 AD45000-15 - Plug NPT1
2 "Mud Pump gear oil lubrication pump unit Type: YB2 112M – 6W 2.2Kw 380V, 5.6A, 940r/min, 50Hz Q= 26L/min
P= 1.4 Mpa 2.2 Kw"
3 "Mud pump charge/feeder pump (pump side) Q= 26L/min
P= 1.4 Mpa 2.2 Kw Specifications
➢ Capacity 200m3/h ➢ Speed 1480 rpm ➢ Power 55 KW ➢ Head 36 m"
"SCHEDULE ID: JZ70D DRILLING RIG FLOOR
MECHANICAL HANDLING TOOLS SPARES"
a "Hydraulic power unit Axial piston pump Pump model CY14- 113
Rated speed 1000rpm
Rated pressure 31.5Mpa"
b "Rig floor pneumatic winch Specification data
➢ Max. lifting traction 50kN
➢ Rated power 21.5HP
➢ Max. length of wire 120meters
➢ Weight approximate 600kg
➢ Max. lifting speed 0.58m/s
➢ Rated air pressure 0.8MPa
➢ Diameter of wire 20mm"
c. QJ-5-SM PNEUMATIC HOST
1 QC010012- Piston
2 QC010010- Piston sleeve
3 QC010014- bearing 6211
4 QC010016- Piston rings
5 QC010017- Piston pins
6 QC010026- Rotary arm
7 Brake band
"SCHEDULE IE: JZ70D DRILLING RIG FLOOR
PNEUMATIC,LUBRICATION AND GREASING SPARES"
a. RIG PNEUMATIC SYSTEM
1 AZ702124-030400 - Safety chain
2 51270424 - 2/3 Port air operated valve K23JK-F40
3 44120501 - Stainless steel ball valve Rc2
4 44120501 - Stainless steel ball valve Rc1
5 44120501 - Stainless steel ball valve Rc1/2
6 5127041001 - Check valve G2
7 5127040706 - Quick exhaust valve G3/8
b. GREASE LUBRICATION SYSTEM
1 AF700201-010906B1 Joint R3/8-M16X1.5
2 5209010358 - Cutting Sleeve 10 (GB3764)
3 6130201794 - Oil Cup M10X1 (JB/T7940.1)
4 5209010355 - Tapered ring 10 (GB3761)
c. OIL LUBRICATION SYSTEM
1 BA702305-020400 - Oil spray line assembly C
2 BA702305-020500 - Oil spray line assembly D
3 BA702305-0210 - Seal cushion
4 51260501004 - Oil suction filter
5 512604100- Throttle valve MG10G1.2
6 51270402000 - Relief valve AQF-E25/0.8
7 3802070111- Pressure gauge (0-1.6MPa) (YN60-1)
"CHEDULE IF: JZ70D DRILLING RIG CIRCULATION
SYSTEM ELECTRICAL SPARES"
a "SHALE SHAKER VIBRATOR MOTORS Specifications
➢ 1.865Kw, 220/300V, 6.9/4.0A, 50Hz"
"SCHEDULE IG: JZ70D DRILLING RIG JC-70D
CONTROLS, CCTV AND SCR MODULES"
a "AIR CONTROL SYSTEM FOR THE
DRAWWORKS"
1 5126040510 - Pressure switch G1/4
2 5127050406 - Ex-proof electromagnetism coil (230VAC)
3 5127050407 - Ex-proof electromagnetism coil (230VDC)
4 5127040702 - Anti-clash loop valve (FP-L6)
5 T002-200.00 - Crown block saver
6 5127050900 - Auto drain valve AD400-04
b ZJ70/4500D DRILLER’S CABIN
1 330401172001101000- Thermo relay 3UA5940-2E
2 "340701060070200000- EX-proof emergency lamp
GBYL-Y2X20"
3 340702061100000000- Projectual light CBB-60HGF1
4 "360701100120010000- DC power supply QUINTPS-100-
240AC/24DC/20"
5 340702061300002000- DC Indicate lamp XB2BVB4C
6 Ex-proof fluorescent light BAY51-2X40
7 JBR6034150 and ACP6034BC- JBR receptacle
c. RIG INDUSTRIAL CLOSED CURCUIT TELEVION CAMERA
1. INDUSTRIAL CCTV
1. General Technical Specifications
"a) Adapt to the environment temperature -18 ° C to +50
° C,"
b) humidity ≤90% (+20 ° C), altitude ≤1500m.
"c) The system should be equipped with explosion-proof,
waterproof, dustproof,
anticorrosive, shock-proof and temperature-proof properties,
and adapt to the
harsh conditions and open-air operation requirements."
"d) The system is reliable, stable, and can be applied to
the
electromagnetic interference environment of rig frequency
conversion
system."
"e) The system can meet the requirements of modular
splitting and
transportation of the rig, and the modules are connected with
a quick plug
device."
"f) Equipped with playback capabilities and a storage
hard disk capable of storing up to 150 hours of video
to provide adequate video recording for on-site data
processing"
g) Standard Compliance
"h) SY/T 10041, GB 3836.1, GB 3836.2, GB 3836.4,
GB/T 4208, GB/T 3797, GB 50115 and API RP500."
i) Technical Data
"Explosion-proof spherical cameras
(HD network integrated color camera,
sensor pixel: 2 million pixels, main bit
stream resolution: 1920×1080)
equipped with rotating head
• Horizontal action 0-345°(±5°)
• horizontal speed: 3.5°/s (±5°
/s)
• Tilt action ±45°(±2°)
• tilt speed: 3.5°/s (± 5°/s QTY4"
"15 "" explosion-proof liquid crystal
display monitor screen with
• four points and four frames to
display various picture
combinations with adjustable
angle.
• cast aluminum flameproof
protective cover QTY1"
Video controller QTY1
"Control keyboard with ability to
control all monitoring screens, can
realize rotation of the head and zoom
and focus of the lens and can switch
the screen of the monitor QTY2"
"Cables with quick plug metallic exproof connector shell
• 150 meters QTY6"
220V/50Hz, 10A power supply interface QTY2
C ZJ70D RIG SCR SYSTEM
"1. AC module
Part No: BMO0521250022 Serial No: 1108-08
Engine: CAT 3512
1500 RPM
1310 Kw
Generator: 1900KVA
600 Volts
3 Phase
50Hz
Flywheel Teeth: 183
Mag Pickup Freq: 4.575Hz at 1500 rpm"